Steering wheel control adapter Fiat 500L, Ducato, Doblo, Dodge RAM Promaster 2012-> CTSFA011.2

Description

Steering wheel control adapter for Citroen / Dodge / Fiat / Opel / Peugeot

Retain the original functions of your steering wheel remote control when replacing your factory radio with an aftermarket one.

Depending on the vehicle equipment and the scope of functions and software of the retrofitted HU, individual operating functions may be omitted or replaced by other functions.

Compare the wiring harness connectors shown with the connectors in your car and make sure they match visually and technically.

Check if one of the listed OEM head units was originally installed.

Before final installation, also check vehicle functionality, vehicle settings and SWC functionality.

Note:

• CAN-Bus
• connector: 52 Pin Fiat
• vehicles without Blue&Me
• OEM touchscreen vehicles, HU date/time setting is not supported
• vehicle settings are not supported
• vehicles with OEM rear view camera connector:
• Reversing camera adapter OEM 52Pin Fiat Camera > article: 771000-2000
• red: Pin 31 Video+
• white: Pin 32 Video –
• black: Pin 33 cover

Make and model:

• Citroen Jumper (250) 05/2014 – 2023***
• Citroen Relay (250) 05/2014 – 2023***
   
• Dodge RAM Promaster 2014-2021*

• Fiat 500L (ZAF 199) 10/2012 – 07/2017**
• Fiat 500L (ZAF 199) 07/2017 – 03/2022**
• Fiat Doblo (ZAF 263) 01/2015 – 06/2022
• Fiat Ducato (ZFA 250) 05/2014 – 11/2021***
   
• Opel Movano Cargo C (Y) 10/2021 – 2023***
   
• Peugeot Boxer (Y) 05/2014 – 2023***

The following signals are available:

• Re-imported vehicles or vehicles with different software may not be feature compatible.
   
• red: ignition terminal +12V 15
• orange: lighting terminal +12V 58
• purple/white: reverse signal +12V
• green: parking brake signal GND
   
• total output load capacity: 100 mA max.
   
• current demand greater than 100 mA:
• 1 relay coil resistance 75 Ohm min.
• 2 relays coil resistance 150 Ohm min.

SWC

*vehicles with OEM 5-inch screen
*vehicles with OEM satellite navigation
*blind spot not supported
**vehicles with VDO OEM HU
***vehicles with open dashboard

Note: SELECT THE CABLE FOR THE RADIO RECEIVER YOU WANT TO INSTALL (TO BE PURCHASED SEPARATELY)                

• ALPINE
• BLAUPUNKT
• BLAUPUNKT NEW YORK / SONY
• CLARION
• JVC
• JVC KW-AVX
• KENWOOD
• NAKAMICHI / PHILIPS
• LG
• PANASONIC
• PANASONIC AV
• PIONEER
• PIONEER AV
• ZENEC
• UNIVERSAL FOR CHINESE RADIO RECEIVERS                      

Features and benefits

• Allows you to install an aftermarket OEM radio and retain the factory steering wheel controls
• Safety: Allows you to keep your hands on the wheel and focus on driving
• Plug and Play, no wire cutting required
• Retains original vehicle features such as date, time, and temperature display
• For interfaces where the phone buttons are supported, the interface allows you to answer/hang up a call in Bluetooth mode: Alpine, Clarion, Kenwood, Pioneer and ZENEC

General installation instructions:

Verification:
1: Check all operational and vehicle setup functions of the OEM HU.
2: Disconnect the voltage-free OEM HU.
3: Verify all interface connections are correct in voltage-free mode.

Connection and connection sequence:
1: Check the settings and hardware configuration of the voltage-free interface.
2: Check the configuration of the voltage-free radio connection cable.
3: Connect the radio connection cable according to the HU retrofit manual.
4: Connect all other connections according to the HU retrofit manual.
5: Connect the entire installation to the vehicle with the main connection last.
6: Configure the interface software according to the instructions in the section text and in the manual.
7: Configure the retrofit device according to the user manual for the steering wheel remote control/camera/FSE/antenna phantom power and other retrofit device.
8: Test the operation of the steering wheel remote control and vehicle

Changes to the interface and cable configuration for connecting the radio:
1: Change the configuration without voltage
2: Reconnect, see above 5 to 8

In case of abnormal operation of the interface or vehicle:
1: Reinstall the OEM HU
2: Operate the OEM HU
3: Determine the CAN bus shutdown
4: Check the hardware configuration of the interface
5: Reconnection after the CAN bus shutdown, see above 5 and 6

More connections, connection changes, alternative connections, loose cable connections or extensions of loose cable connections mentioned in the information text or instructions are for guidance purposes only and are the information of a trained specialist installer.

More connections, changes to the wiring configuration within the wiring harness, or the use of alternative connections or connection extensions:
1: Connections and modifications should only be made by trained installers.
2: Connections and modifications should be checked before connection to ensure they meet any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.
3: Before connection, check connections and modifications for functionality and correctness by taking measurements and comparing them with the vehicle's wiring diagram.
4: Connections and modifications are made at the user's own risk and without any guarantee of performance. 5: Connections and modifications are made
at the user's own risk and without any guarantee of damage to the vehicle, retrofit device, or interface.
6: Modifications to the pre-assembled wiring harness may void the product warranty.